CT 285 (2 Wege)   Floorstanding as in K+T 3/2016

Technical data
  • impedance: 8 Ohm
  • sensivity (2,83V/1m): 90 dB
  • size (HxWxD): 960 x 238 x 330 mm
  • frequency range (-8dB): 40 - 21000 Hz
  • crossover frequency(s): 2000 Hz
  • speaker type: bass reflex

CT 285-2Weg is a 2 way floorstanding speaker with a small fullrange driver as tweeter and a bigger fullrange driver for the bass range.

CT285-FAST is developed by Holger Barske and Thomas Schmidt.

The cabinet contains two full range loudspeakers: the small Visaton FRS 5X and the bigger Visaton BG 20. With both there are three different variants:

The crossover consists of a third order high-pass filter (18 dB per octave slope) for the tweeter and a second order low-pass filter for the woofer.

The frequency response of this speaker is linear. The decay spectrum is good. At low volume, i.e. 85 dB at 1 m, the nonlinear distortions are not higher than 0,5% between 300 Hz and 10 000 Hz and doesn't exceed 1,5% at 95 dB at 1 m.

Our kit consists of

  • Visaton FRS 5X, 8 Ohm
  • Visaton BG 20, 8 Ohm
  • Bass reflex tube HP70, 68x160 mm, black
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • 3x Damping Sonofil 100 x 35 cm for 20 litres
  • 0,5x Foam N25, 100x50x4 cm, black
  • Binding Post PK31, gold plated (one pair, red and black)
  • 3m Speaker cable 2x1.5 mm2, transparent
  • 1,5x Pan screws 3.5x17 black, cross recess, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 4.7 uF / 400 Vdc
  • Audaphon MKP CAP Superior 8.2 uF / 400 Vdc
  • 2x Audaphon MKT CAP 10 uF / 160 Vdc
  • 1.0 mm air core coil, 2.2 mH/0.89 Ohm
  • 0.7 mm air core coil, 0.56 mH/0.55 Ohm
  • Metal-oxide resistor, 10W 10 Ohm (brown-black-black)

Kit without cabinet, price per speaker   EUR 105,00 excl. VAT: € 88.24 / $ 108.53

Important: The costomised ring for the Visaton FRS 5X is not included in our kit.

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. All capacitors are of type MKP (polypropylen). In series to the tweeter a high quality Clarity-Cap capacitor of type ESA is delivered.

Kit with high-end-crossover without cabinet, price per speaker   EUR 130,00 excl. VAT: € 109.24 / $ 134.37

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 11,42 excl. VAT: € 9.60 / $ 11.80

universal PCBs

If you prefer to mount the crossover components on a 140 x 102 mm universal PCB instead on wood:
Universal PCB RA140, order no.. I-2765, price per unit:   EUR 3,70 excl. VAT: € 3.11 / $ 3.82
We recommend one board per kit (two boards for a speaker pair)


Home   Klang+Ton Overview